Pro 2700-PSI Brushless 1.2-GPM Electric Pressure Washer

Hello Inxs, Thank you for your question. A 15 Amp breaker can typically handle up to 1,800 Watts. This unit is ~1,680 Watts. If this is the only product on the circuit, it should work.

Hello Fubear, We're sorry to hear that you are in need of a replacement part. You may purchase a replacement motor pump assembly by calling 1-888-909-6757 and referencing the part number below. Part Number: C1101044-00

Hello Boyet, Please try purging the air from the pump. To complete this task, set up the unit as per usual and ensure you are not using an extension cord. Remove any nozzle that may be connected at the end of the wand. Make sure that you have a green light on the GFCI on the power cord. Turn your garden hose on but leave the pressure washer turned OFF. With the pressure washer turned off, squeeze on the trigger for about 3 minutes – allowing the water to run through the unit at no pressure. In doing so, you are bleeding the unit out of any air that may be stuck in the pump. After 3 minutes, turn the unit on. If it is running, reinstall one of your clean nozzles and continue using the unit. If this issue persists, we ask that you please contact us directly at 1-888-909-6757 or via email at info@greenworkstools.com and use the subject line "Help Request - Reviewer Response".

Hello Wads, Believe it or not, this could have to do with a faulty nozzle or excess air trapped in the pump. Please try out the troubleshooting exactly as listed below and let me know your outcome! Purge any excess air from the pump. Set up the unit as per usual and ensure you are not using an extension cord. Remove any nozzle that may be connected at the end of the wand. Make sure that you have a green light on the GFCI on the power cord. Turn your garden hose on but leave the pressure washer turned OFF. With the pressure washer turned off, squeeze on the trigger for about 3 minutes – allowing the water to run through the unit at no pressure. In doing so, you are bleeding the unit out of any air that may be stuck in the pump. After 3 minutes, turn the unit on. If it is running, reinstall one of your clean nozzles and continue using the unit. TRY ALL NOZZLES (a faulty/dirty nozzle may cause this reaction). For further troubleshooting and assistance, we kindly request that you contact us directly at 1-888-909-6757 or by sending an email to info@greenworkstools.com.

Hello TheMom, Yes, this item will work very well for vinyl siding or house washing projects. If you have wood frames that are painted, you may run the risk of removing any potential loose paint so please use caution unless you are planning to repaint and reseal. Apply soap in advance and then rinse thoroughly. Good luck with your projects!

Hello Twoberry, We are sorry to hear that you're experiencing issues with the onboard soap tank! Please ensure that you have the black soap nozzle installed. If you have the black soap nozzle installed, and soap still is not coming out. Please try out the following troubleshooting suggestions: 1) Dilute your detergent. Ensure that you are using a designated pressure washer soap and that it has been diluted as per the instructions on the product. If the product does not mention dilution, its possible that the soap is simply too thick for this product. In that case, we recommend diluting it 10 parts water to 1-part soap. 2) Ensure that the filter at the end of the suction tube is not clogged, if it is, run some warm water through the filter to clear the blockage. 3) Ensure the suction tube is probably connected. 4) The spray tip could be clogged. Blow out or remove debris with your nozzle cleaning tool or a fine needle. Occasionally we suggest cleaning all nozzles by soaking all of your nozzles in a half and half mixture of warm water and white vinegar. Soak all the nozzles for about an hour and then proceed to poke your nozzle cleaning tool or paper clip through the end of the nozzle hole to poke out any debris. After you have done this, rinse them with warm water. Your nozzles will now be free of any obstructions causing the unit to malfunction. If you are still experiencing issues, kindly send us an email through the customer contact page located on our website or give us a call at 1-888-909-6757 for further assistance with this matter.

Hello Rocko, Here is a link to our 1500PSI pressure washer! https://www.greenworkstools.com/1500-psi-electric-pressure-washer

Hello fcabr, We do apologize for the existing wait times. With the spring season here, so is our busiest time of year. Our team is doing our best to operate under existing guidelines as well. We know your time is valuable and our team is working diligently to be in contact with each waiting customer as quickly as we can be while giving each person the attention they deserve. Unfortunately, we understand this is not ideal, but we want to be clear that this is not a normal experience for Greenworks.